How to Install 2022-2023 Toyota Tundra SS6 LED Fog Light Kit

The SS6 LED Fog Light Kit for the 2022-2023 Toyota Tundra allows you to mount a pair of Stage Series 6" LED Light Bars as Tundra LED fog lights. The following installation guide will provide you with detailed instructions on how to remove the factory Tundra fog lights and install the SS6 LED Fog Light Bar Kit on the 2022-2023 Toyota Tundra. Check out our installation video, or continue reading for step-by-step instructions below!

Installation Tools

• Phillips Screwdriver
• Phillips Screwdriver Bit
• Ratchet/Extensions
• Plastic Trim Removal Tool 

Installation Video

Mounting Instructions

Step 1 - Loosen the Grille

Using a 10mm socket, remove the four bolts from the top of the grille.

Step 2 - Disconnect Connectors

If equipped, disconnect the connectors from both corners of the grille as shown in the image below.

Step 3 - Remove Wheel Well Screws

Using a 10mm socket, remove the four screws from inside the wheel well. If equipped with over-fender molding, remove the additional screw from the bottom inside of the wheel well opening. Repeat this step on the other side of the vehicle.

Step 4 - Remove Bumper Bolts

Remove the four 10mm bolts from underneath the bumper. If not equipped with a front spoiler, there will be four screws underneath the bumper that will need to be removed as well.

Step 5 - Remove Grille/Bumper Assembly

Pull out on both sides to release the clips holding the grille in place. Then remove the front grille/bumper assembly by pulling forward.

Step 6 - Remove Bumper Panel Screws

Using a Phillips screwdriver, remove the six screws securing each corner bumper panel. Then remove the two screws on top of the grille. 

Step 7 - Loosen Upper Grille Surround

Using a plastic trim removal tool, push through the ten tabs securing the upper grille surround.

Step 8 - Remove Corner Bumper Panels

Remove the corner bumper panels by pushing through the seven tabs securing them in place. 

Step 9 - Remove Bumper Molding

Using a plastic trim removal tool, remove the front bumper molding by releasing the clips and pulling outward.

Step 10 - Remove Fog Lights

Using a Phillips screwdriver, remove the two screws securing the factory fog light to the front bumper. Then remove the factory fog light from the vehicle, and unplug the factory fog light connector. Repeat this step on the other side of the vehicle.

Step 11 - Install Fog Light Brackets

Install the four included fog light brackets onto the sides of your new Stage Series 6” light bars using the included hardware as shown.

Step 12 - Install LED Light Bars

Install your new light bar and bracket into the factory location using the factory screws. Repeat this step on the other side of the vehicle.

Step 13 - Connect Vehicle Harness

Use an included adapter wire to connect the light bar to the vehicle harness on each side.

Step 14 - Reinstall Grille/bumper Assembly

Bring the bumper assembly to the vehicle to test and aim. Snap each end into the fender clips, and reinstall four 10mm bolts along the top of the grille. Plug in the two connectors at each corner of the grille if equipped.

Step 15 - Test Function

Test the function of the lights. If either light does not turn on, try flipping the connector 180° where it plugs into the vehicle harness. Aim the lights as shown on the back of this guide. Then, tighten down the bolts to secure the lightbars in place.

Step 16 - Resecure Assembly Panels

Reverse step 14 to remove the grille/bumper assembly from the vehicle again, then reinstall the bumper assembly by reversing steps 1 through 9. Then reverse steps 6 through 9 to resecure the grille/bumper assembly panels.

Aiming Instructions

Step 17 - Position Vehicle for Aiming

Park your vehicle 25 feet away from a wall or garage door on a level surface.

Step 18 - Loosen LED Light Bar Bolts

Loosen the M6 bolts on each side of your SS6 lightbar, just enough to allow you to adjust the lightbar.

Step 19 - Measure Mounting Height

On your vehicle, measure the distance between the ground and the center of your SS6 lightbar. This is your mounting height.

Step 20 - Mark Mounting Height On Wall

Mark the mounting height on the wall or garage door using tape.

Step 21 - Mark Fog Cut-Off Line

Add another piece of tape four inches below the mounting height. This is your fog light cut-off line.

Step 22 - Aim SS6 LED Light Bars

Aim your SS6 lightbar on each side, so that the top of the beam pattern is on the cutoff line mark.

Step 23 - Complete Installation

Tighten the M6 bolts back down to complete the installation. Do not overtighten or use power tools to torque them down.